All alternatives
View full reportTechnical parameters
| Power | |
|---|---|
| No-load supply current | I 0 | Emitter: ≤ 15 mA Receiver: ≤ 15 mA at 24 V Operating voltage |
| Operating voltage | U B | 10 ... 30 V DC |
| Switching current | max. 100 mA , resistive load |
| Switching voltage | max. 30 V DC |
| Voltage drop | U d | ≤ 1.5 V DC |
| AC and DC characteristics | |
| Ripple | max. 10 % |
| Switching frequency | f | 1000 Hz |
| Environment and package | |
| Ambient temperature | -40 ... 60 °C (-40 ... 140 °F) |
| Height | 50.6 mm |
| Height 50.6 mm Width 15 mm Depth 41.7 mm | Height | 50.6 mm | Width | 15 mm | Depth | 41.7 mm |
| Storage temperature | -40 ... 70 °C (-40 ... 158 °F) |
| Other | |
| Alignment aid | LED red (in receiver lens) illuminated constantly: beam is interrupted, flashes: reaching switching point, off: sufficient operating reserve |
| Ambient light limit | EN 60947-5-2 : 40000 Lux |
| CCC approval | CCC approval / marking not required for products rated ≤36 V |
| Communication interface | IEC 61131-9 |
| Compatible master port type | A |
| Connection | Connector plug, M8 x 1, 3 pin, rotatable by 90° |
| Control elements | Receiver: light/dark switch |
| Degree of protection | IP67 / IP69 / IP69K |
| Depth | 41.7 mm |
| Device ID | Emitter: 0x111401 (1119233) Receiver: 0x111301 (1118977) |
| Device profile | Identification and diagnosis Smart Sensor: Receiver: type 2.4 Emitter: - |
| Diagnostic Coverage (DC) | 60 % |
| Diameter of the light spot | approx. 850 mm at a distance of 25 m |
| Effective detection range | 0 ... 25 m |
| Emitter | OBE25M-R200-S-IO-V3 |
| Function indicator | Yellow LED: Permanently lit - light path clear Permanently off - object detected Flashing (4 Hz) - insufficient operating reserve |
| Housing | PC (Polycarbonate) |
| Housing PC (Polycarbonate) Optical face PMMA | Housing | PC (Polycarbonate) | Optical face | PMMA |
| Interface type | IO-Link ( via C/Q = pin 4 ) |
| IO-Link revision | 1.1 |
| LED risk group labelling | exempt group |
| Light source | LED |
| Light type | modulated visible red light |
| Mass | Emitter: approx. 35 g receiver: approx. 35 g |
| Min. cycle time | 2.3 ms |
| Mission Time (T M ) | 20 a |
| MTTF d | 462 a |
| Opening angle | approx. 2 ° |
| Operation indicator | LED green: constantly on - power on flashing (4Hz) - short circuit flashing with short break (1 Hz) - IO-Link mode |
| Optical face | PMMA |
| Process data width | Emitter: Process data input: 0 bit Process data output: 1 bit Receiver: Process data input: 2 bit Process data output: 2 bit |
| Product standard | EN 60947-5-2 |
| Protection class | III |
| Receiver | OBE25M-R200-EP-IO-V3 |
| Response time | 0.5 ms |
| Signal output | 1 push-pull (4 in 1) output, short-circuit protected, reverse polarity protected, overvoltage protected |
| SIO mode support | yes |
| Switching type | The switching type of the sensor is adjustable. The default setting is: C/Q - Pin4: NPN normally open / dark-on, PNP normally closed / light-on, IO-Link |
| Test input | emitter deactivation at +U B |
| Threshold detection range | 33 m |
| Transfer rate | COM2 (38.4 kBit/s) |
| UL approval | E87056 , cULus Listed , class 2 power supply , type rating 1 |
| Usage category | DC-12 and DC-13 |
| Width | 15 mm |
Documents
No documents are linked to this part yet.