81805

Active

Single head system

All alternatives

Technical parameters

Power
No-load supply current	I 0 \| ≤ 50 mA
Operating voltage	U B \| 10 ... 30 V DC , ripple 10 % SS
Output current	< 12 mA
Rated operating current	I e \| 200 mA , short-circuit/overload protected
Voltage drop	U d \| ≤ 2 V
AC and DC characteristics
0 Level 0 ... 1 V 1 Level 4 V ... U B Input impedance > 12 kΩ Output current < 12 mA Pulse length 0.5 ... 300 ms (level 1) Pulse interval ≥ 33 ms (level 0)	0 Level \| 0 ... 1 V \| 1 Level \| 4 V ... U B \| Input impedance \| > 12 kΩ \| Output current \| < 12 mA \| Pulse length \| 0.5 ... 300 ms (level 1) \| Pulse interval \| ≥ 33 ms (level 0)
Input impedance	> 12 kΩ
Repeat accuracy	≤ 0.1 % of full-scale value
Response delay	minimum: 60 ms factory setting: 120 ms
Switching frequency	f \| ≤ 5 Hz
Time delay before availability	t v \| ≤ 1600 ms
Transducer frequency	approx. 175 kHz
Environment and package
Ambient temperature	-40 ... 70 °C (-40 ... 158 °F)
Height	40 mm
Height 40 mm Width 40 mm Length 40 mm	Height \| 40 mm \| Width \| 40 mm \| Length \| 40 mm
Storage temperature	-40 ... 85 °C (-40 ... 185 °F)
Temperature influence	< 1.5 % of full-scale value
Other
0 Level	0 ... 1 V
1 Level	4 V ... U B
Adjustment range	80 ... 2000 mm
Beam width	wide
Bending radius	> 37.3 mm , fixed installation > 74.7 mm , movable installation
Cable	PUR
CCC approval	CCC approval / marking not required for products rated ≤36 V
Common mode operation	≤ 30 Hz
Common mode operation ≤ 30 Hz Multiplex operation ≤ 33 Hz / n , n = number of sensors , n ≤ 10 (factory setting: n = 5 )	Common mode operation \| ≤ 30 Hz \| Multiplex operation \| ≤ 33 Hz / n , n = number of sensors , n ≤ 10 (factory setting: n = 5 )
Connection type	cable , 5-pin
Core cross section	5 x 0.82 mm 2
Dead band	0 ... 60 mm
Degree of protection	IP67
Evaluation procedure	averaging (MxN) M = 5 N = 2
Housing	PA-GF35
Housing PA-GF35 Cable PUR Transducer epoxy resin/hollow glass sphere mixture; polyurethane foam	Housing \| PA-GF35 \| Cable \| PUR \| Transducer \| epoxy resin/hollow glass sphere mixture; polyurethane foam
Input/output type	1 synchronization connection, bidirectional
Interface type	Serial interface (programming adapter required) 9600 BPS, no parity, 8 data bits, 1 stop bit
LED green	Operating display
LED red	error
LED yellow 1	switching state switch output 1
LED yellow 2	switching state switch output 2
Length	L \| 2 m
Mass	345 g
Multiplex operation	≤ 33 Hz / n , n = number of sensors , n ≤ 10 (factory setting: n = 5 )
Output 1	near switch point: 80 mm far switch point: 2000 mm Output mode: Window mode output behavior: NO contact
Output 2	near switch point: 150 mm far switch point: 1000 mm Output mode: Window mode output behavior: NO contact
Output type	2 switch outputs PNP, NO/NC, programmable
Pulse interval	≥ 33 ms (level 0)
Pulse length	0.5 ... 300 ms (level 1)
Range hysteresis	H \| programmable , preset to 1 mm
Sensing range	60 ... 2000 mm
Sheath diameter	7.25 mm
Sheath diameter 7.25 mm Bending radius > 37.3 mm , fixed installation > 74.7 mm , movable installation Core cross section 5 x 0.82 mm 2 Length L 2 m	Sheath diameter \| 7.25 mm \| Bending radius \| > 37.3 mm , fixed installation > 74.7 mm , movable installation \| Core cross section \| 5 x 0.82 mm 2 \| Length \| L \| 2 m
Standards	EN IEC 60947-5-2:2020 IEC 60947-5-2:2019
Standards EN IEC 60947-5-2:2020 IEC 60947-5-2:2019	Standards \| EN IEC 60947-5-2:2020 IEC 60947-5-2:2019
Standard target plate	100 mm x 100 mm
Supplementary information	Switch settings of the external programming adapter: "output load": pull-down "output logic": inv
Transducer	epoxy resin/hollow glass sphere mixture; polyurethane foam
UL approval	cULus Listed, Class 2 Power Source
Width	40 mm

Documents

No documents are linked to this part yet.