All alternatives
View full reportTechnical parameters
| Power | |
|---|---|
| Current | ≤ 100 mA per output, ≤ 100 mA total |
| Input current | ≤ 4 mA (limited internally) |
| Rated operating current | I e | ≤ 40 mA (without inputs/outputs)/max. 160 mA |
| Rated operating voltage | U e | 26.5 ... 31.6 V from AS-Interface (PELV) |
| Supply | from AS-Interface |
| Voltage | 12 ... 31 V |
| AC and DC characteristics | |
| Noise immunity | EN 61000-6-2:2005, EN 61326-1:2006, EN 62026-2:2013 |
| Signal delay | < 1 ms (input/AS-Interface) |
| Environment and package | |
| Ambient temperature | -25 ... 70 °C (-13 ... 158 °F) |
| Height | 10 mm |
| Height 10 mm Width 36 mm Length 39.5 mm | Height | 10 mm | Width | 36 mm | Length | 39.5 mm |
| Storage temperature | -25 ... 85 °C (-13 ... 185 °F) |
| Other | |
| 0 (unattenuated) | ≤ 0.15 mA |
| 0 (unattenuated) ≤ 0.15 mA 1 (attenuated) ≥ 1.3 mA | 0 (unattenuated) | ≤ 0.15 mA | 1 (attenuated) | ≥ 1.3 mA |
| 1 (attenuated) | ≥ 1.3 mA |
| Altitude | ≤ 5000 m above MSL |
| AS-Interface | EN 62026-2:2013 |
| AS-Interface specification | V3.0 |
| Climatic conditions | For indoor use only |
| Connection | 200 mm, PVC cable 0.5 mm 2 |
| D0 | IN1 OUT1 |
| D0 IN1 OUT1 D1 IN2 OUT2 D2 IN3 OUT3 D3 IN4 OUT4 | D0 | IN1 OUT1 | D1 | IN2 OUT2 | D2 | IN3 OUT3 | D3 | IN4 OUT4 |
| D1 | IN2 OUT2 |
| D2 | IN3 OUT3 |
| D3 | IN4 OUT4 |
| Data bits (function via AS-Interface) | Input Output |
| Degree of protection | EN 60529:2000 |
| Directive 2014/30/EU | EN 62026-2:2013 |
| Directive 2014/30/EU EN 62026-2:2013 | Directive 2014/30/EU | EN 62026-2:2013 |
| Emitted interference | EN 61000-6-4:2007 |
| Fieldbus standard | EN 62026-2:2013 |
| Housing | Polyamide hot-melt adhesive |
| Housing Polyamide hot-melt adhesive | Housing | Polyamide hot-melt adhesive |
| ID1 code | 7 |
| ID2 code | 7 |
| ID code | A |
| IO code | 7 |
| LED FAULT | error display; LED red red: communication error or address is 0 red flashing: overload of outputs |
| LED IN | switching state (input); 4 LED yellow |
| LED OUT | Switching state (output); 4 LED yellow |
| LED PWR | AS-Interface voltage; green LED green: voltage OK flashing green: address 0 |
| Length | 39.5 mm |
| Mass | 33 g |
| MTBF | 267 a |
| Node type | A/B node |
| Note | This device is maintenance-free. If the device is used in a manner not specified by the manufaturer, the protection provided by the device may be impaired. |
| Number/Type | 4 inputs for mechanical contacts |
| P0 | not used |
| P1 | Input filter P1 = 0 input filter on, pulse suppression ≤ 2 ms P1 = 1 input filter off (default settings) |
| P2 | Synchronous mode P2 = 0 synchronous mode on P2 = 1 synchronous mode off (default settings) |
| P3 | not used |
| Parameter bits (programmable via AS-i) | function |
| Pollution degree | 2 |
| Profile | S-7.A.7 |
| Protection class | III |
| Relative humidity | 85 % , non-condensing |
| Required gateway specification | ≥ V3.0 |
| Shock and impact resistance | 30 g, 11 ms in 6 spatial directions, 3 shocks 10 g, 16 ms in 6 spatial directions, 1000 shocks |
| Surge protection | U e : overvoltage category II, safe isolated power supplies (PELV) |
| UL approval | Protection class IP20 is not included in the UL approval. The protection class is tested by Pepperl+Fuchs. |
| UL File Number | E223772 |
| Usage category | DC-1 "general use" (ohmic and weak inductive loads in accordance with IEC 60947) |
| Vibration resistance | 0.35 mm 10 ... 57 Hz , 5 g, 57 Hz ... 150 Hz, 10 cycles |
| Width | 36 mm |
Documents
No documents are linked to this part yet.