139020

Active

Universal distance sensor, measurement to reflector, IO-Link interface, measuring method PRT, measuring range up to 150 m, red laser light, laser class 1, push-pull output, M12 plug

See alternatives Ask AI FAE

All alternatives

View full report

Technical parameters

Power
No-load supply current	I 0 \| < 25 mA at 24 V Operating voltage
Operating voltage	U B \| 10 ... 30 V DC 18 ... 30 V from IO-Link
Switching current	max. 100 mA , resistive load
Switching voltage	max. 30 V DC
Voltage drop	U d \| ≤ 1.5 V DC
AC and DC characteristics
Absolute accuracy	typ. ± 20 mm (including influence of temperature)
Repeat accuracy	< 6 mm
Resolution	1 mm
Ripple	10 % within the supply tolerance
Time delay before availability	t v \| < 900 ms
Environment and package
Ambient temperature	-30 ... 60 °C (-22 ... 140 °F)
Height	50.6 mm
Height 50.6 mm Width 15 mm Depth 41.7 mm	Height \| 50.6 mm \| Width \| 15 mm \| Depth \| 41.7 mm
Storage temperature	-40 ... 70 °C (-40 ... 158 °F)
Temperature influence	< 0.25 mm/K
Other
Ambient light limit	10000 Lux
Average data age	3 ms (default), 6 ms , 12 ms , 25 ms , 50 ms , 100 ms , adjustable
Beam divergence	2 mrad
CCC approval	CCC approval / marking not required for products rated ≤36 V
Communication interface	IEC 61131-9 / IO-Link V1.1.3
Connection	4-pin, M12 x 1 connector, 90° rotatable
Control elements	Teach-In key
Degree of protection	IP67 / IP69 / IP69K
Depth	41.7 mm
Device ID	1121041 (0x111B11)
Device profile	Identification and Diagnosis - I&D Smart Sensor - SSP 4.2.1
Diagnostic Coverage (DC)	0 %
Diameter of the light spot	< 20 mm at 10 m
FDA approval	IEC 60825-1:2014 Complies with 21 CFR 1040.10 and 1040.11 except for conformance with IEC 60825-1 Ed. 3 as described in Laser Notice 56, dated May 8, 2019.
Function indicator	LED yellow: constantly on - switch output active constantly off - switch output inactive
Housing	PC (Polycarbonate)
Housing PC (Polycarbonate) Optical face PMMA	Housing \| PC (Polycarbonate) \| Optical face \| PMMA
Interface type	IO-Link ( via C/Q = pin 4 )
IO-Link revision	1.1
Laser class	1
Laser safety	EN 60825-1:2014
Light source	laser diode
Light type	modulated visible red light
Mass	approx. 37 g
Max. Motion velocity	10 m/s
max. pulse energy	< 1.3 nJ
Measured value output	1 ms
Measuring method	Pulse Ranging Technology (PRT)
Measuring range	0.2 ... 150 m
Min. cycle time	4 ms
Mission Time (T M )	20 a
MTTF d	> 300 a
Note	LASER LIGHT , DO NOT STARE INTO BEAM
Operation indicator	LED green: constantly on - power on flashing (4Hz) - short circuit flashing with short break (1 Hz) - IO-Link mode
Optical face	PMMA
Process data	Input 6 Byte - measurement value 4 Byte - scaling factor 8 Bit - signal quality 2 Bit - switching signal 1 1 Bit - switching signal 2 1 Bit - diagnosis signals n Bit - additional signals n Bit Output 2 Bit - sensor control function 1 Bit - evaluation control function 1 Bit
Product standard	EN 61000-6-2, EN 61000-6-3
Protection class	III
Pulse length	4 ns
Reference target	OFR-500/500
Repetition rate	300 kHz
Signal output	2x push-pull outputs, reverse polarity protected, surge-proof
SIO mode support	yes
Switching output 1	Q1: switching signal high-active , Window mode 6000 ... 9000 mm
Switching output 2	Q2: switching signal high-active , Window mode 4000 ... 8000 mm
Switching type	The default setting is: C/Q - Pin4: push-pull output, IO-Link Q2 - Pin2: push-pull output
Teach-in indicator	Teach-In : LED yellow/green; equiphase flashing; 2,5 Hz Teach Error:LED green/yellow non equiphase flashing; 8.0 Hz
Transfer rate	COM2 (38.4 kBit/s)
UL approval	E87056 , cULus Listed , class 2 power supply , type rating 1
Usage category	DC-12 and DC-13
Vendor ID	1 (0x0001)
Warm up time	5 min
Wave length	660 nm
Width	15 mm

Documents

No documents are linked to this part yet.