搜索结果:CD4541
共 27 条- 匹配型号27
- 有数据手册7
- 涉及品牌7
产品搜索结果共 27 条
| 对比 | 产品型号 | 品牌 | 分类 | 产品描述 | 技术资料 | 替代 | 操作 |
|---|---|---|---|---|---|---|---|
| 数据手册1 | 查看详情 | ||||||
| 门和反相器 | 芯伯乐XBLW为您提供国产型号CD4541的封装、参数规格、替代方案、数据手册等信息;免费样品、技术方案支持请咨询本公司 | 查看详情 | |||||
| 可编程定时器和振荡器 | IC OSC PROG TIMER 100KHZ 14DIP | 数据手册1 | 查看详情 | ||||
| 可编程定时器和振荡器 | IC OSC PROG TIMER 100KHZ 14SOIC | 查看详情 | |||||
| 可编程定时器和振荡器 | IC OSC PROG TIMER 100KHZ 14SOIC | 查看详情 | |||||
| 可编程定时器和振荡器 | IC OSC PROG TIMER 100KHZ 14SOIC | 查看详情 | |||||
| 可编程定时器和振荡器 | IC OSC PROG TIMER 100KHZ 14SOIC | 查看详情 | |||||
| 可编程定时器和振荡器 | IC OSC PROG TIMER 100KHZ 14SO | 查看详情 | |||||
| 可编程定时器和振荡器 | IC OSC PROG TIMER 100KHZ 14TSSOP | 查看详情 | |||||
| 奇偶校验发生器和校验器 | CD4541B programmable timer consists of a 16-stage binary counter, an oscillator that is controlled by external R-C components (2 resistors and a capacitor), an automatic power-on reset circuit, and output control logic. The counter increments on positive-edge clock transitions and can also be reset via the MASTER RESET input. The output from this timer is the Q or Q\ output from the 8th, 10th, 13th, or 16th counter stage. The desired stage is chosen using time-select inputs A and B (see Frequency Select Table). The output is available in either of two modes selectable via the MODE input, pin 10 (see Truth Table). When this MODE input is a logic "1", the output will be a continuous square wave having a frequency equal to the oscillator frequency divided by 2 N . With the MODE input set to logic "0" and after a MASTER RESET is initiated, the output (assuming Q output has been selected) changes from a low to a high state after 2 N-1 counts and remains in that state until another MASTER RESET pulse is applied or the MODE input is set to a logic "1". Timing is initialized by setting the AUTO RESET input (pin 5) to logic "0" and turning power on. If pin 5 is set to logic "1", the AUTO RESET circuit is disabled and counting will not start until after a positive MASTER RESET pulse is applied and returns to a low level. The AUTO RESET consumes an appreciable amount of power and should not be used if low-power operation is desired. For reliable automatic power-on reset, V DD should be greater than 5V. The RC oscillator, shown in Figure 2, oscillates with a frequency determined by the RC network and is calculated using: Where f is between 1kHz and 100kHz and R S and 2R TC . | 数据手册5 | 查看详情 | ||||
| 门和反相器 | 可编程定时器 | 数据手册1 | 查看详情 | ||||
| 门和反相器 | 查看详情 | ||||||
| 可编程定时器和振荡器 | BINARY COUNTER | 数据手册1 | 查看详情 | ||||
| 可编程定时器和振荡器 | PROGRAMMABLE TIMER | 查看详情 | |||||
| 可编程定时器和振荡器 | IC OSC PROG TIMER 100KHZ 14SOIC | 查看详情 | |||||
| 可编程定时器和振荡器 | IC OSC PROG TIMER 100KHZ 14SOIC | 查看详情 | |||||
| 可编程定时器和振荡器 | IC OSC PROG TIMER 100KHZ 14DIP | 查看详情 | |||||
| 可编程定时器和振荡器 | PROGRAMMABLE TIMER | 查看详情 | |||||
| 可编程定时器和振荡器 | PROGRAMMABLE TIMER | 查看详情 | |||||
| 可编程定时器和振荡器 | IC OSC PROG TIMER 100KHZ 14SOIC | 查看详情 |
没找到想要的型号?
让 AI 帮你联网查找,或者直接告诉客服。
申请芯片样品
填写型号和样品需求,供样安排确认后会联系你。