全部替代型号
查看完整报告技术参数
| 电源 | |
|---|---|
| No-load supply current | I 0 | < 16 mA at 24 V supply voltage |
| Operating voltage | U B | 10 ... 30 V DC |
| Switching current | max. 100 mA , resistive load |
| Switching voltage | max. 30 V DC |
| Voltage drop | U d | ≤ 1.5 V DC |
| 交流 / 直流特性 | |
| Repeat accuracy | < 0.5 % |
| Resolution | 0.1 mm |
| Ripple | max. 10 % |
| 环境与封装 | |
| Ambient temperature | 10 ... 60 °C (50 ... 140 °F) |
| Height | 50.6 mm |
| Height 50.6 mm Width 15 mm Depth 41.7 mm | Height | 50.6 mm | Width | 15 mm | Depth | 41.7 mm |
| Storage temperature | -40 ... 70 °C (-40 ... 158 °F) |
| Temperature drift | 0.05 %/K |
| 其他 | |
| Ambient light limit | EN 60947-5-2 : 45000 Lux |
| Angle deviation | max. +/- 1.5 ° |
| Beam divergence | > 5 mrad, d63 < 2,8 mm in the range of 350 mm ... 800 mm |
| Cable length | 2 m |
| CCC approval | CCC approval / marking not required for products rated ≤36 V |
| Communication interface | IEC 61131-9 |
| Compatible master port type | A |
| Connection | 2 m fixed cable |
| Control elements | Teach-In key |
| Degree of protection | IP67 / IP69 / IP69K |
| Depth | 41.7 mm |
| Device ID | 0x11190A (1120522) |
| Device profile | Identification and diagnosis Smart Sensor type 0/type 3.3 |
| Diagnostic Coverage (DC) | 0 % |
| Diameter of the light spot | approx. 3 mm at a distance of 300 mm |
| FDA approval | IEC 60825-1:2014 Complies with 21 CFR 1040.10 and 1040.11 except for conformance with IEC 60825-1 Ed. 3 as described in Laser Notice 56, dated May 8, 2019. |
| Function indicator | LED yellow: constantly on - switch output active constantly off - switch output inactive |
| Housing | PC (Polycarbonate) |
| Housing PC (Polycarbonate) Optical face PMMA | Housing | PC (Polycarbonate) | Optical face | PMMA |
| Interface type | IO-Link ( via C/Q = BK ) |
| IO-Link revision | 1.1 |
| Laser class | 1 |
| Laser safety | EN 60825-1:2014 |
| Light source | laser diode |
| Light type | modulated visible red light |
| Linearity error | 0.5 % |
| Mass | approx. 73 g |
| max. pulse energy | < 40 nJ |
| Measuring range | 100 ... 300 mm |
| Min. cycle time | 3 ms |
| Mission Time (T M ) | 20 a |
| MTTF d | 560 a |
| Note | LASER LIGHT , DO NOT STARE INTO BEAM |
| Opening angle | approx. 0.3 ° |
| Operation indicator | LED green: constantly on - power on flashing (4Hz) - short circuit flashing with short break (1 Hz) - IO-Link mode |
| Optical face | PMMA |
| Process data width | Process data input 4 byte Process data output 2 bits |
| Product standard | EN 60947-5-2 |
| Protection class | III |
| Pulse length | 5.5 µs |
| Reference target | standard white, 100 mm x 100 mm |
| Repetition rate | approx. 2.4 kHz |
| Response time | 2 ms |
| Signal output | 2 push-pull (4 in 1) outputs, short-circuit protected, reverse polarity protected, overvoltage protected |
| SIO mode support | yes |
| Switching type | The default setting is: C/Q - BK: NPN normally open, PNP normally closed, IO-Link Q2 - WH: NPN normally open, PNP normally closed |
| Transfer rate | COM2 (38.4 kBit/s) |
| UL approval | E87056 , cULus Listed , class 2 power supply , type rating 1 |
| Usage category | DC-12 and DC-13 |
| Warm up time | 5 min |
| Wave length | 680 nm |
| Width | 15 mm |
器件图片
技术资料
该型号暂未收录资料。