全部替代型号
查看完整报告技术参数
| 电源 | |
|---|---|
| No-load supply current | I 0 | < 20 mA at 24 V supply voltage |
| Operating voltage | U B | 10 ... 30 V DC |
| Switching current | max. 100 mA , resistive load |
| Switching voltage | max. 30 V DC |
| Voltage drop | U d | ≤ 1.5 V DC |
| 交流 / 直流特性 | |
| Ripple | max. 10 % |
| Switching frequency | f | 2000 Hz |
| 环境与封装 | |
| Ambient temperature | -40 ... 60 °C (-40 ... 140 °F) |
| Height | 44.5 mm |
| Height 44.5 mm Width 11 mm Depth 21.5 mm | Height | 44.5 mm | Width | 11 mm | Depth | 21.5 mm |
| Storage temperature | -40 ... 70 °C (-40 ... 158 °F) |
| 其他 | |
| Ambient light limit | EN 60947-5-2 |
| Beam divergence | > 5 mrad d63 < 2 mm in the range of 250 mm ... 750 mm |
| Communication interface | IEC 61131-9 |
| Compatible master port type | A |
| Connection | M8 x 1 connector, 3-pin |
| Control elements | Light-on/dark-on changeover switch |
| Degree of protection | IP67 / IP69 / IP69K |
| Depth | 21.5 mm |
| Device ID | 0x110202 (1114626) |
| Diagnostic Coverage (DC) | 0 % |
| Diameter of the light spot | approx. 30 mm at a distance of 12 m |
| Effective detection range | 0 ... 12 m |
| FDA approval | IEC 60825-1:2014 Complies with 21 CFR 1040.10 and 1040.11 except for conformance with IEC 60825-1 Ed. 3 as described in Laser Notice 56, dated May 8, 2019. |
| Function indicator | Yellow LED: Permanently lit - light path clear Permanently off - object detected Flashing (4 Hz) - insufficient operating reserve |
| Housing | PC (Polycarbonate) |
| Housing PC (Polycarbonate) Optical face PMMA | Housing | PC (Polycarbonate) | Optical face | PMMA |
| Interface type | IO-Link ( via C/Q = pin 4 ) |
| IO-Link revision | 1.1 |
| Laser class | 1 |
| Laser safety | EN 60825-1:2014 |
| Light source | laser diode |
| Light type | modulated visible red light |
| Mass | approx. 10 g |
| max. pulse energy | 9.6 nJ |
| Min. cycle time | 2.3 ms |
| Mission Time (T M ) | 20 a |
| MTTF d | 672 a |
| Note | LASER LIGHT , DO NOT STARE INTO BEAM |
| Opening angle | approx. 0.3 ° |
| Operation indicator | LED green: constantly on - power on flashing (4Hz) - short circuit flashing with short break (1 Hz) - IO-Link mode |
| Optical face | PMMA |
| Parameterization indicator | IO link communication: green LED goes out briefly (1 Hz) |
| Polarization filter | yes |
| Process data width | Process data input 2 Bit Process data output 2 Bit |
| Product standard | EN 60947-5-2 |
| Protection class | III |
| Pulse length | 1.6 µs |
| Reference target | Reflector REF-MH50 |
| Reflector distance | 0.16 ... 12 m |
| Repetition rate | max. 17.6 kHz |
| Response time | 250 µs |
| Signal output | 1 push-pull (4 in 1) output, short-circuit protected, reverse polarity protected, overvoltage protected |
| SIO mode support | yes |
| Switching type | The switching type of the sensor is adjustable. The default setting is: C/Q - Pin4: NPN normally open / dark-on, PNP normally closed / light-on, IO-Link |
| Threshold detection range | 15 m |
| Transfer rate | COM2 (38.4 kBit/s) |
| UL approval | E87056 , cULus Listed , class 2 power supply , type rating 1 |
| Usage category | DC-12 and DC-13 |
| Wave length | 680 nm |
| Width | 11 mm |
器件图片
技术资料
该型号暂未收录资料。