全部替代型号
查看完整报告技术参数
| 电源 | |
|---|---|
| No-load supply current | I 0 | ≤ 10 mA |
| Off-state current | I r | 0 ... 0.5 mA typ. 0.01 mA |
| Off-state current T U =40 °C, switching element off | ≤ 100 µA |
| Off-state current T U =40 °C, switching element off ≤ 100 µA | Off-state current T U =40 °C, switching element off | ≤ 100 µA |
| Operating current | I L | 0 ... 200 mA |
| Operating voltage | U B | 10 ... 30 V |
| Operating voltage indicator | LED, green |
| Voltage drop | U d | ≤ 2.8 V |
| Voltage drop I L = 100 mA, switching element on | U d | 1 ... 2.6 V typ. 1.8 V |
| Voltage drop I L = 10 mA, switching element on | U d | 0.8 ... 2.2 V typ. 1.4 V |
| Voltage drop I L = 1 mA, switching element on | U d | 0.5 ... 2.3 V typ. 0.9 V |
| Voltage drop I L = 200 mA, switching element on | U d | 1.2 ... 2.8 V typ. 2 V |
| Voltage drop I L = 20 mA, switching element on | U d | 0.9 ... 2.3 V typ. 1.5 V |
| Voltage drop I L = 50 mA, switching element on | U d | 0.9 ... 2.5 V typ. 1.6 V |
| 交流 / 直流特性 | |
| Switching frequency | f | 0 ... 100 Hz |
| Time delay before availability | t v | ≤ 100 ms |
| 环境与封装 | |
| Ambient temperature | -25 ... 70 °C (-13 ... 158 °F) |
| Height | 55 mm |
| Height 55 mm Width 55 mm Length 128 mm | Height | 55 mm | Width | 55 mm | Length | 128 mm |
| Note Sealing ring: Hole diameter 7 / 10.5 / 13 / 16 mm The dimension of the connection cable must correspond to the hole selected on the sealing ring. | Note | Sealing ring: Hole diameter 7 / 10.5 / 13 / 16 mm The dimension of the connection cable must correspond to the hole selected on the sealing ring. |
| Storage temperature | -25 ... 85 °C (-13 ... 185 °F) |
| 其他 | |
| Actual operating distance | s r | 36 ... 44 mm typ. 40 mm |
| Assured operating distance | s a | 0 ... 32.4 mm |
| CCC approval | CCC approval / marking not required for products rated ≤36 V |
| Connection type | terminal compartment |
| Core cross section | up to 2.5 mm 2 |
| Degree of protection | IP68 |
| Diagnostic Coverage (DC) | 0 % |
| Housing material | PBT with Viton seals and PVDF screwed connection |
| Hysteresis | H | 1 ... 10 % typ. 5 % |
| Information for connection | A maximum of two conductors with the same core cross section may be mounted on one terminal connection! tightening torque 1.2 Nm + 10 % |
| Installation | non-flush |
| Length | 128 mm |
| Maximum core cross-section | without wire end ferrules 2.5 mm 2 , with connector sleeves 1.5 mm 2 |
| Minimum core cross-section | without wire end ferrules 0.5 mm 2 , with connector sleeves 0.34 mm 2 |
| Mission Time (T M ) | 20 a |
| MTTF d | 684 a |
| Note | Sealing ring: Hole diameter 7 / 10.5 / 13 / 16 mm The dimension of the connection cable must correspond to the hole selected on the sealing ring. |
| Output polarity | DC |
| Output type | PNP |
| Rated operating distance | s n | 40 mm |
| Reduction factor r 304 | 0.8 |
| Reduction factor r Al | 0.5 |
| Reduction factor r Cu | 0.45 |
| Reverse polarity protection | reverse polarity protected |
| Sensing face | PBT |
| Short-circuit protection | pulsing |
| Standards | EN IEC 60947-5-2 |
| Standards EN IEC 60947-5-2 | Standards | EN IEC 60947-5-2 |
| Switching function | Normally open (NO) |
| Switching state indicator | LED, yellow |
| UL approval | cULus Listed Load Type: Resistive Circuitry: Class 2 Power Source Enclosure Type Rating: Type 1 Supply/Switching Voltage: 30 V DC Output Switching Current: 200 mA |
| Width | 55 mm |
器件图片
技术资料
该型号暂未收录资料。