134431

134431

在产

Solenoid Driver

问 AI FAE

全部替代型号

查看完整报告

技术参数

电源
CurrentI e | 45 mA
Current limitI max | 45 mA
Inrush current≤ 200 mA after 100 µs
Maximum safe voltageU m | 250 V (Attention! The rated voltage can be lower.)
Maximum safe voltage U m 250 V (Attention! The rated voltage can be lower.)Maximum safe voltage | U m | 250 V (Attention! The rated voltage can be lower.)
Open loop voltageU s | min. 23.6 V
Output/power supplysafe electrical isolation acc. to IEC/EN 60079-11, rated insulation voltage 300 V rms
PowerP o | 850 mW (angular characteristic curve)
Power consumptionmax. 3.5 W at 45 mA output current
Power supply/Outputreinforced insulation according to IEC/EN 61010-1, rated insulation voltage 300 V eff
Rated currentI r | 0-signal: typ. 1.6 mA at 1.5 V DC; typ. 8 mA at 3 V DC (maximum leakage current DO card) 1-signal: ≥ 20 mA (minimum load current DO card)
Rated voltageU r | 18 ... 30 V DC
Test currentmax. 350 µA , calculated by I LFD = 3.3 V / (10 kΩ + R Load )
Test current max. 350 µA , calculated by I LFD = 3.3 V / (10 kΩ + R Load )Test current | max. 350 µA , calculated by I LFD = 3.3 V / (10 kΩ + R Load )
VoltageU e | ≥ 15 V
交流 / 直流特性
Energized/De-energized delay≤ 20 ms / ≤ 20 ms
环境与封装
Ambient temperature-40 ... 70 °C (-40 ... 158 °F) , both channels configured in the bus powered mode of operation -40 ... 60 °C (-40 ... 140 °F) , all other configurations extended ambient temperature range up to 70 °C (158 °F) for other configurations, refer to manual for necessary mounting conditions
Dimensions20 x 119 x 115 mm (0.8 x 4.7 x 4.5 inch) (W x H x D) , housing type B2
Mountingon 35 mm DIN mounting rail acc. to EN 60715:2001
其他
Configurationvia DIP switches
ConnectionPower Rail or terminals 14+, 15-
Connection sidecontrol side
Control drawing116-0488
Control drawing 116-0488Control drawing | 116-0488
Control elementsDIP switch
Degree of protectionIP20
Directive 2014/30/EUEN 61326-1:2013 (industrial locations)
Directive 2014/30/EU EN 61326-1:2013 (industrial locations)Directive 2014/30/EU | EN 61326-1:2013 (industrial locations)
Directive 2014/34/EUEN IEC 60079-0:2018+AC:2020 , EN 60079-7:2015+A1:2018 , EN 60079-11:2012
Directive 2014/34/EU EN IEC 60079-0:2018+AC:2020 , EN 60079-7:2015+A1:2018 , EN 60079-11:2012Directive 2014/34/EU | EN IEC 60079-0:2018+AC:2020 , EN 60079-7:2015+A1:2018 , EN 60079-11:2012
Display elementsLEDs
Electromagnetic compatibilityNE 21:2017 , EN IEC 61326-1:2021 (industrial locations) , EN IEC 61326-3-2:2018 For further information see system description.
EU-type examination certificateFIDI 21 ATEX 0091 X
IECEx certificateIECEx FIDI 21.0009X
IECEx certificate IECEx FIDI 21.0009X IECEx marking Ex ec [ia Ga] IIC T4 Gc [Ex ia Da] IIIC [Ex ia Ma] IIECEx certificate | IECEx FIDI 21.0009X | IECEx marking | Ex ec [ia Ga] IIC T4 Gc [Ex ia Da] IIIC [Ex ia Ma] I
IECEx markingEx ec [ia Ga] IIC T4 Gc [Ex ia Da] IIIC [Ex ia Ma] I
Input/Outputreinforced insulation according to IEC/EN 61010-1, rated insulation voltage 300 V eff
Internal resistanceR i | 167 Ω
Internal resistorR i | approx. 167 Ω
Labelingspace for labeling at the front
Loadnominal 0.05 ... 20 kΩ , valid range for line fault detection (LFD)
MarkingII 3(1)G Ex ec [ia Ga] IIC T4 Gc [exsign] II (1)D [Ex ia Da] IIIC [exsign] I (M1) [Ex ia Ma] I
Massapprox. 150 g
OutputEx ia Refer to certificate for alternative parameters.
Signal levelloop powered 1-signal: 18 ... 30 V DC 0-signal: 0 ... 5 V DC bus powered 1-signal: 15 ... 30 V DC (current limited to 5 mA) 0-signal: 0 ... 5 V DC
Signal typeDigital Output
Supplementary informationObserve the certificates, declarations of conformity, instruction manuals, and manuals where applicable. For information see www.pepperl-fuchs.com.
Test pulse lengthmax. 2 ms from DO card
UL approvalE106378

器件图片

技术资料

该型号暂未收录资料。