122151

在产

Solenoid Driver

全部替代型号

技术参数

电源
Current	I e \| ≤ 45 mA
Current limit	I max \| 45 mA
Inrush current	≤ 200 mA after 100 µs
Maximum safe voltage	U m \| 250 V (Attention! The rated voltage can be lower.)
Maximum safe voltage U m 250 V (Attention! The rated voltage can be lower.)	Maximum safe voltage \| U m \| 250 V (Attention! The rated voltage can be lower.)
Open loop voltage	U s \| min. 23.6 V
Output/power supply	safe electrical isolation acc. to IEC/EN 60079-11, rated insulation voltage 300 V rms
Power	P o \| 850 mW (angular characteristic curve)
Power consumption	max. 3.5 W at 45 mA output current
Power dissipation	< 2 W
Power supply/Output	reinforced insulation according to IEC/EN 61010-1, rated insulation voltage 300 V eff
Rated current	I r \| loop powered 0-signal: typ. 1.6 mA at 1.5 V DC; typ. 8 mA at 3 V DC (maximum leakage current DO card) 1-signal: ≥ 20 mA (minimum load current DO card) bus powered 1-signal: 5 mA
Rated voltage	U r \| 18 ... 30 V DC
Test current	max. 350 µA , calculated by I LFD = 3.3 V / (10 kΩ + R Load )
Test current max. 350 µA , calculated by I LFD = 3.3 V / (10 kΩ + R Load )	Test current \| max. 350 µA , calculated by I LFD = 3.3 V / (10 kΩ + R Load )
Voltage	U e \| ≥ 15 V
交流 / 直流特性
Energized/De-energized delay	≤ 20 ms / ≤ 20 ms
Protection against electrical shock	UL 61010-1:2019
环境与封装
Ambient temperature	-40 ... 70 °C (-40 ... 158 °F)
Dimensions	12.5 x 119 x 114 mm (0.5 x 4.7 x 4.5 inch) (W x H x D) , housing type A2
Mounting	on 35 mm DIN mounting rail acc. to EN 60715:2001
其他
Certificate	UL 23 ATEX 3065 X
Configuration	via DIP switches
Connection	Power Rail or terminals 9+, 10- bus powered
Connection side	control side
Control drawing	116-0496 (cULus)
Control drawing 116-0496 (cULus)	Control drawing \| 116-0496 (cULus)
Control elements	DIP switch
Degree of protection	IEC 60529:2013
Directive 2014/30/EU	EN 61326-1:2013 (industrial locations)
Directive 2014/30/EU EN 61326-1:2013 (industrial locations)	Directive 2014/30/EU \| EN 61326-1:2013 (industrial locations)
Directive 2014/34/EU	EN IEC 60079-0:2018+AC:2020 , EN 60079-7:2015+A1:2018 , EN 60079-11:2012
Directive 2014/34/EU EN IEC 60079-0:2018+AC:2020 , EN 60079-7:2015+A1:2018 , EN 60079-11:2012	Directive 2014/34/EU \| EN IEC 60079-0:2018+AC:2020 , EN 60079-7:2015+A1:2018 , EN 60079-11:2012
Display elements	LEDs
Electromagnetic compatibility	NE 21:2017 , EN IEC 61326-1:2021 (industrial locations) , EN IEC 61326-3-2:2018 For further information see system description.
EU-type examination certificate	UL 23 ATEX 3027 X
IECEx certificate	IECEx ULD 23.0016X
IECEx certificate IECEx ULD 23.0016X IECEx marking [Ex ia Ga] IIC , [Ex ia Da] IIIC , [Ex ia Ma] I Ex ec IIC T4 Gc	IECEx certificate \| IECEx ULD 23.0016X \| IECEx marking \| [Ex ia Ga] IIC , [Ex ia Da] IIIC , [Ex ia Ma] I Ex ec IIC T4 Gc
IECEx marking	[Ex ia Ga] IIC , [Ex ia Da] IIIC , [Ex ia Ma] I Ex ec IIC T4 Gc
Input/Output	reinforced insulation according to IEC/EN 61010-1, rated insulation voltage 300 V eff
Internal resistance	R i \| 167 Ω
Internal resistor	R i \| approx. 167 Ω
Labeling	space for labeling at the front
Load	nominal 0.05 ... 20 kΩ , valid range for line fault detection (LFD)
Marking	II (1)G [Ex ia Ga] IIC [exsign] II (1)D [Ex ia Da] IIIC [exsign] I (M1) [Ex ia Ma] I
Marking II 3G Ex ec IIC T4 Gc	Marking \| II 3G Ex ec IIC T4 Gc
Mass	approx. 105 g
Output	Ex ia Refer to certificate for alternative parameters.
Signal level	loop powered 1-signal: 18 ... 30 V DC (current limited to ≥ 20 mA) 0-signal: 0 ... 5 V DC bus powered 1-signal: 15 ... 24 V DC (current limited at 5 mA) 0-signal: 0 ... 5 V DC
Signal type	Digital Output
Supplementary information	Observe the certificates, declarations of conformity, instruction manuals, and manuals where applicable. For information see www.pepperl-fuchs.com.
Test pulse length	max. 2 ms from DO card
UL approval	E106378

器件图片

实物照片 · 产品库

技术资料

该型号暂未收录资料。